I’m not really a shotgun guy. I don’t find twelve gauge all that much fun to shoot, but I always had one. I’ve owned a few semiautomatic shotguns, including the original Benelli M1 Super 90. I noticed a knock-off of the Benelli M2 by Military Armament Corporation at the gun store the other day. The price was hard to resist (sub $400), so I didn’t.

Now, I’ve heard a lot about the quality of Turkish shotguns being as bad as some of their handguns (Tisas) are good. But at $400, I figure if it’s even halfway to the Benelli, it would be worth it.

So how good is it? Wrong question. How bad is it?

First, the good stuff: It actually comes with chokes, something Benellis I’ve bought don’t, plus the tools to adjust the chokes, the sights, the angle and distance of the stock. It’s got adjustable ghost ring sights, a rail for optics, and is very pointable and light. It looks good, and at first pass, the action runs well and smoothly.

I got the M2 home last week, and broke it down, cleaned and lubed it. I noted a few aluminum shavings here and there — probably missed in the cleaning phase of the production. I took it out for a run today (Monday). I put a total of only 50 shells through it (plus another 30 in a Kel Tec KS7). It’s pretty light at six and a half pounds, and you feel the stouter stuff after a few boxes.

The M2 uses the time-tested Benelli inertial recoil system, so it should run some of the lighter stuff that the ARGO system wouldn’t. In this case, I started with some Norma reduced recoil buckshot. Out of 20 rounds, I had a single failure to eject. Not a bas start. I tried a couple of shorty Aguilas, anticipating they wouldn’t cycle. I was correct. Back to Norma Performance buckshot for 20 rounds. The Turkenelli ran them without issue, save for one failure to eject. Again, for the first time out, now awful. Hornady Black buckshot ran like a top save for one failure to fire that looked to be the round. (It was three years old.) Ten rounds of slug with no malfunctions. All 2 3/4rds, no magnums.

Accuracy was decent, though the reduced recoil shot about two inches high at 15 yards. It was spot on with the Black and slug. While the shorties didn’t cycle, they did pattern spot on at point of aim.

So far, so good. As usual, when I got home, I started cleaning the weapons, starting with the MAC 2. First thing I noted was that the magazine tube really didn’t want to unscrew. I also noticed a bunch of aluminum shavings from the threads and there was some damage from the brace that holds the mag tube and barrel. It had worked it’s way forward a bit during firing.

I don’t mean a few shavings like you’d find from having not cleaned the area…

This is just from the magazine tube being unscrewed. But wait, there’s more. I pulled the tube and dismounted the barrel. Here’s the front of the receiver:

Note not just the impact damage where it meets the barrel; look inside the receiver there. But we’re just getting started, Dear Reader. I pulled the bolt and took it down. Here’s the bolt:

Aluminum shavings. I popped the trigger assembly, using the firing pin retaining pin, as they instructed. That was a mistake:

Nice. And before you say anything, yes — you could do this with the Benelli and not break stuff. With the trigger guard off, the real fun started. There were aluminum shavings and damage everywhere. Remember, this is only 50 shells, nothing hot; in fact, half of it was reduced recoil.

No — that’s not dirt. How’d the bolt look? It was scuffed at the front of the face.

After half an hour of cleaning I had a nice collection of metal filings and had to go over the cleaning mat twice just to get rid of the bits. I even vacuumed the floor under my seat. And once I was done and oiled the weapon…? More shavings.

That’s after I cleaned the hell out of the gun. There was still more.

Aluminum, admittedly, seems a bit of a bad choice for a 12 gauge, but I’ve seen it from other manufacturers. None of their stuff spontaneously shed aluminum, like Arianna Grande losing weight. And again — 50 rounds of normal factory ammunition.

So is it worth it? NO. Not just no, hell no. Steer away from this. I can only imagine how they’ve messed up the ARGO system in their 1014s. Yes, it’s sub-$400, but you can get a Maverick, which won’t shred itself with normal operation. Hell, my cheap Kel Tec has hundreds of rounds through it and even eats shorty shells: no failures.

I have a warranty claim into MAC for the firing pin retaining pin and a request to replace the weapon. Will I fire this thing again? Unlikely. If it’s shedding metal, it’s going to fail somewhere.

Update: I reached out to SDS in Tennessee the same day as this occurred, and I will give them this — their customer service folks are on it. They confirmed that this is not a normal event and that the weapon needs to be replaced. The lady on the CS line was very helpful, especially as I got in touch with them right at the end of their work day.

More as events unfold…